MyHouseAnswersPractical home guides
Menu

Why Is My Dishwasher Not Draining?

Reference notes

Published by

· About the publisher

An open dishwasher with dishes on its lower rack.
In this guide

Updated

First distinguish water confined to the recessed filter area from water covering the dishwasher floor. Then note whether the wash ended, whether the water ever left, and whether it returned later. These observations separate normal retained water, an interrupted cycle, an appliance drain fault, and a problem at the sink connection.

Stop if water is escaping or electrical signs appear

Stop using the machine for a floor leak, burning smell, damaged wiring, repeated breaker trips, or unusual grinding. Do not step into water to reach a plug or pull out a built-in appliance. Arrange safe isolation and service. Do not reach blindly into the sump: broken glass can be hidden in dirty water. Keep children away from the open door and wastewater.

Never add sink drain cleaner to a dishwasher or mix cleaning chemicals. If chemicals have already been added, avoid further handling and tell the service provider exactly what was used. Do not improvise a suction or pump repair inside the appliance.

Where the water remains matters as much as its presence

Three different drainage reports
PatternUseful next distinction
A little water confined to the recessed filter area.Compare the exact model’s normal retained-water description; do not apply another dishwasher’s depth limit.
Water covers the tub floor and never left.Record completion status, code and any permitted normal Cancel/Drain result.
The machine emptied, then water returned later.Record the timing relative to sink/disposer use and ask for appliance/connection assessment.

Whirlpool’s linked guidance explains that some water is intentionally retained around its filter-area seals. That is different from abnormal standing water across the tub. The same guide separately discusses drain obstructions and air-gap arrangements; finding one normal pocket does not prove the entire drainage path is sound.

For a new installation, ask the installer to verify the model-specific hose/connection arrangement and show normal drainage without leaks or return flow. This is not permission to remove a disposer plug or substitute a hose loop for a required air gap.

Check where the water is and when it appeared

A little water visible only inside a recessed filter well can be intentional on some models. Whirlpool’s water-retention guidance describes this for its dishwashers. Compare your exact model’s manual rather than applying a universal depth measurement. Water spread across the tub floor, a drain error, or new dirty water returning after a cycle deserves investigation.

Record whether the program completed or was interrupted by an open door, power loss, or cancellation. If there are no leaks or other warning signs, use the manual’s Cancel/Drain command once if it provides one. Do not keep restarting full washes. If water remains, record the error and stop further trial cycles.

If it drains but water later returns, note the timing relative to sink or disposer use. This is a different symptom from water that never left. Do not deliberately fill an already backed-up sink to reproduce the problem.

For a new installation or recently replaced disposer

A fault present from the first cycle is a reason to contact the installer before assuming a failed pump. Whirlpool’s installation guidance identifies restricted or incorrectly routed drain hoses and an unremoved disposer inlet plug as possible causes. Not every installation uses a disposer. The route, connection and any air-gap requirements must match the appliance instructions and local rules.

Photograph an accessible under-sink connection without detaching it. Do not knock out a plug, pull the dishwasher from its cabinet, or reroute the hose based on a general diagram. Ask the installer to verify the connection and demonstrate normal drainage without leaks or water returning.

If the sink or an air gap also backs up

Use the sink’s recent drainage history. If it is slow, backs up, or receives dishwasher wastewater, the shared plumbing needs attention. The slow-sink guide explains how to distinguish a local fixture problem from wider drainage symptoms. Avoid using either fixture while wastewater is backing up.

If your installation has an air gap on the sink or worktop, water escaping there is useful information for the plumber. Owner-accessible cleaning depends on that fitting’s instructions. Do not seal it, bypass it, or assume a hose loop is an interchangeable substitute. Leave uncertain connections and inaccessible restrictions to the appropriate installer or plumber.

Limit filter work to owner maintenance

With the appliance stopped, cool and isolated as the manual directs, clean an owner-removable filter if fitted. Follow its unlocking, cleaning and refitting procedure. Some filter systems are not designed for the same disassembly. Do not force a housing, remove a pump cover without model-specific permission, or run the machine with the filter missing.

Visible accessible debris can be reported or removed only using the manual’s safe method. Do not feel around under water or reach into a disposer. A clean filter does not prove the hose, pump, valve or household drain is sound. If clearing the filter does not restore normal drainage, that is the limit of this check.

Give service the drainage pattern

Provide the model, program, completion status, water location, error code, first occurrence, and any recent installation work. Describe sounds already observed; do not run a humming or grinding pump again to make a recording. Noise alone cannot establish which part needs replacement.

After correction, ask for confirmation that the appliance empties as its design requires, the sink connection stays dry, and wastewater does not return. If drainage is restored but dishes remain dirty, use the separate dishwasher cleaning-performance guide. These are related symptoms, but an unsatisfactory wash does not by itself diagnose a drain fault.

Reference notes

Retained water and drain-failure patterns

Whirlpool · Appliance manufacturer

Whirlpool explains water remaining at cycle end and the role of the installation/drain connection. It supports noting location and timing before calling all retained water a fault.

Apply it to your situation: Normal retained-water locations and owner-accessible parts depend on the dishwasher model.

Read the Whirlpool reference →

DISHWASHER DRAIN HOSE INSTALLATION 2020 REDESIGN

W Service

An installation demonstration for the referenced Whirlpool design. It helps explain the drain-hose discussion with an installer; required routing and heights come from your own model and local plumbing rules.

Watch on YouTube. The player connects to YouTube after you select Load.

Verify this video on the manufacturer’s website

About the publisher